Sale!

Compressor 230 volt 400 litre/minuteTX-3

  • FAD 400 litre/minute
  • Working pressure 8 bar
  • Maximum pressure 10 bar
  • Receiver 100 litre
  • 5 years of warranty

795,00 537,00 Excl. Btw

SKU: 62875515 Category: Tag:

Product Description

The TX-3 SS is a best seller in the javac compressor range, originally this compressor was equipped with a 3-pole engine hence the TX-3 designation, but we upgraded the pump to get 25% more power now. Is therefore also equipped with a unique 4 PK engine at 230 V. This gives a flow rate of 400 liters at 0 bar and 360 lt. at 6 Bar, with a working pressure of 10 Bar, and yet this pump is running only 900 Rpm with a suction rate of 450 lt./min). 

Built around a 100-liter thick-walled tank (hence the weight of 120 kg …), our compressors have a small buffer tank, which means that E-motors always start in zero load, so we avoid using motors with very high Couple. This gives 2 major advantages: no peak load = lower power consumption and the ability to rotate in continuous load (this is best done with a regular compressor …)

It goes without saying that it is desirable to determine the capacity of your compressor to achieve a rest of 30% on its capacity. In addition, the compressor is equipped with an automatic start / stop system (Prestostat), a safety group, and a practical 2-speed reducer to control the compressor itself. There are also 2 Orion couplings for direct air intake and an output Of ½ “for connection to a ring line in the workhouse. This compressor stands on 2 strong full-wheel wheels, allowing for frequent moving.

The quality of compressed air is achieved by getting it as cool as possible in the tank, which significantly reduces condensation and is directly responsible for the quality of compressed air. The TX-3 is equipped with a cast steel V-pump, which together with the ribbon-cooled duct ensures optimum cooling of the compressed air. As described above, the speed is limited to 900 rpm, which causes the pump to not heat hot and makes it much less hot. This is possible because of the fact that we use standard concentric valves instead of butterfly valves, which are a lot more expensive, the result is read in much higher efficiency, less heat development, and finally superior compressed air quality. Although the water supply is limited to the TX-3 compressors, we recommend using compressed air machines, sandblasting, sprayers, etc., a centrifugal filter or compressed air dryer.

The maintenance of this compressor is limited to the regular discharge of the boiler of the condensate water, and after 300 hours of oil replacement, only use the javac compressor oil that separates the condensate water from the oil. Certainly never do multigrade oil on the pump, this leads to heavy compressor pump damage, basically any compressor pump </ p>

Technical details

Engine

4 PK

Voltage

230 V mono

Driving

V-riem

Possible capacity

450 L

Issued capacity

400 L

Boiler

100 L

Speed

850 tpm

Alloy pump

Cast steel

Cylinders

2 in V

Ignition system

Interbuffer

Bore (mm)

2*65

Workload

10 bar

Dimensions (cm)

108*84*42

Weight

120 kg

References product

62875515

All our goods can be either picked up or delivered . The delivery costs are as follows:

Belgium:

• Small machine shipping class: 7 per product • Shipping class large machines: 45 per product

The Netherlands:

• Small class shipping class: 20 per product • Large-scale shipping class: 65 per product

France:

• This depends on the zone within France. You will see this on the checkout page.

Other countries:

• On request via info@javac.be

Reviews

There are no reviews yet.

Be the first to review “Compressor 230 volt 400 litre/minuteTX-3”